C-band (* Note 1) erbium doped fiber Pre-amplifier (PA amplifier for short) is an amplifier specially used for weak optical signals in the range of - 45dbm ~ - 25dBm. The typical gain of small signal is as high as 35 ~ 45 dB and has low noise figure. It is usually used before a photodetector to improve its detection ability for weak optical signals.
C-band (* Note 1) erbium doped fiber Pre-amplifier (PA amplifier for short) is an amplifier specially used for weak optical signals in the range of - 45dbm ~ - 25dBm. The typical gain of small signal is as high as 35 ~ 45 dB and has low noise figure. It is usually used before a photodetector to improve its detection ability for weak optical signals.
Features | Applications |
n Wide operating wavelength | n Fiber Communication |
n High Gain | n Fiber Sensing |
n Low Noise | n Fiber Laser |
Parameters | Unit | Typical Value | Remarks | |
Product Number | - | EDFA-PA-35 | EDFA-PA-45 | |
Operating Wavelength | nm | 1530~1565nm | C-band | |
Input signal power | dBm | -35~-25 | -45~-25 | |
Small signal gain | dB | 35@-35dBm Input | 45@-45dBm Input | |
Noise Figure | dB | ≤4.5 | ||
Polarization dependent gain | dB | ≤0.3 | ||
Polarization mode dispersion | ps | ≤0.5 | ||
Input/Output Isolation | dB | >35 | ||
Optical power monitoring | - | Output Power | ||
Optical fiber and connectors | - | SMF-28,FC/APC | ||
Control Mode | - | Automatic Current Control(ACC) |
General Parameters | Benchtop | Module |
Control Function | Push Button/RS232 serial communication | RS232 serial communication |
Remote control port | Optional | DB9 Female |
Power Supply | AC100~240V, <30W | DC5V, <15W |
Dimensions | 260(W)×280(D)×120(H)mm | 125(W)×150(D)×20(H)mm |
Operation Temperature | -5~+35°C | |
Operation Humidity | 0~70% |
Ordering Information/ Product Code | |||||
EDFA | Wavelength | Type | Optical Gain | Fiber | Packaging |
C=C band | PA=Pre Amplifier | 35=35dB@-35dBm 45=45dB@-45dBm | SM=Single-mode fiber | M=module B=Benchtop |
*Note 1: This EDFA product can be used to amplify any single or multiple wavelength signals within its operating wavelength range, but the flatness of the gain spectrum is not considered when multiple wavelength signals are input. As shown in the figure on this page, the EDFA-C-PA-35 small signal amplifier can achieve high-gain amplification for input signals of different wavelengths within the C-band (note that multiple wavelengths in the figure are not simultaneously input into the EDFA). When the input power of a single wavelength is -35dBm, the effective gain is greater than 35dB, and the signal-to-background noise ratio of the amplified signal is greater than 30dB.
C-band (* Note 1) erbium doped fiber Pre-amplifier (PA amplifier for short) is an amplifier specially used for weak optical signals in the range of - 45dbm ~ - 25dBm. The typical gain of small signal is as high as 35 ~ 45 dB and has low noise figure. It is usually used before a photodetector to improve its detection ability for weak optical signals.
Features | Applications |
n Wide operating wavelength | n Fiber Communication |
n High Gain | n Fiber Sensing |
n Low Noise | n Fiber Laser |
Parameters | Unit | Typical Value | Remarks | |
Product Number | - | EDFA-PA-35 | EDFA-PA-45 | |
Operating Wavelength | nm | 1530~1565nm | C-band | |
Input signal power | dBm | -35~-25 | -45~-25 | |
Small signal gain | dB | 35@-35dBm Input | 45@-45dBm Input | |
Noise Figure | dB | ≤4.5 | ||
Polarization dependent gain | dB | ≤0.3 | ||
Polarization mode dispersion | ps | ≤0.5 | ||
Input/Output Isolation | dB | >35 | ||
Optical power monitoring | - | Output Power | ||
Optical fiber and connectors | - | SMF-28,FC/APC | ||
Control Mode | - | Automatic Current Control(ACC) |
General Parameters | Benchtop | Module |
Control Function | Push Button/RS232 serial communication | RS232 serial communication |
Remote control port | Optional | DB9 Female |
Power Supply | AC100~240V, <30W | DC5V, <15W |
Dimensions | 260(W)×280(D)×120(H)mm | 125(W)×150(D)×20(H)mm |
Operation Temperature | -5~+35°C | |
Operation Humidity | 0~70% |
Ordering Information/ Product Code | |||||
EDFA | Wavelength | Type | Optical Gain | Fiber | Packaging |
C=C band | PA=Pre Amplifier | 35=35dB@-35dBm 45=45dB@-45dBm | SM=Single-mode fiber | M=module B=Benchtop |
*Note 1: This EDFA product can be used to amplify any single or multiple wavelength signals within its operating wavelength range, but the flatness of the gain spectrum is not considered when multiple wavelength signals are input. As shown in the figure on this page, the EDFA-C-PA-35 small signal amplifier can achieve high-gain amplification for input signals of different wavelengths within the C-band (note that multiple wavelengths in the figure are not simultaneously input into the EDFA). When the input power of a single wavelength is -35dBm, the effective gain is greater than 35dB, and the signal-to-background noise ratio of the amplified signal is greater than 30dB.